Videotek VTM-2000 Specifications Page 189
- Page / 240
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Alarm Descriptions
VTM Series Installation and Operation Handbook
5-11
LTC/VITC Compare (TC Sync)
The LTC/VITC (TC Sync) alarm occurs when LTC and VITC are compared and differ
beyond the threshold (1 to 30 frames) selection for a period in excess of the duration
setting.
DVITC Time Code Alarm Error Types
The DVITC Time Code Alarms are listed below.
DVITC Loss of Time Code
The DVITC Loss of Time Code alarm occurs when no DVITC Time Code in the video
signal is detected for a period in excess of the duration setting.
DVITC Line
The DVITC Line alarm is used to select the line number on which the D-VITC time
code is detected for the “D-VITC Continuity” and “D-VITC CRC” fields. When time
code is not detected on the selected line number, the alarm activates.
DVITC Continuity
The DVITC Continuity alarm occurs when a break or interruption in the digital vertical
interval time code (VITC) frames occur for a period in excess of the duration setting.
DVITC CRC
The DVITC CRC alarm occurs when the cyclic redundancy check (CRC) within the
digital vertical interval time code field does not correlate with the embedded CRC for a
period in excess of the duration setting
TS Alarms Descriptions (VTM-OPT ASI)
The TS Alarms menu contents are listed below.
Alarm Reporting Setup
The TS Alarm Reporting Setup menu is used to accesses the Alarm Reporting Matrix.
In the Alarm Reporting Matrix select what functions each Alarm will trigger when an
alarm is activated. An alarm occurrence can trigger a log indication, sound, SNMP
trap, GPI OUT 1, GPI OUT 2, Freeze, and Data Capture.
Loss of Signal
The Loss of Signal alarm is activated when the signal carrier is not detected.
CRC Change
The CRC change alarm occurs when the selected table’s CRC information changes.
The selectable monitored tables are PAT, PMT, STT, MGT, VCT, RRT, EIT, and
ETT.
- VTM Series 1
- About This Document 4
- DIRECTIVE 4
- Contents 10
- Section 1 ♦ Introduction 23
- VTM Series Configuration 24
- Video Standards Supported 27
- Introduction 28
- Service and Support 29
- Section 2 ♦ Installation 31
- Rack Mounting the VTM Series 32
- Connecting the VTM Series 33
- Ethernet Setup 34
- Installation 35
- Using the Bypass Feature 38
- Types of Controls 40
- Front Panel Illumination 40
- Sleep Mode 42
- Selecting a Pane 42
- Function Not Allowed Message 43
- Option Not Installed Message 43
- External Reference 45
- Pane Overview 46
- The Waveform Display 47
- Eye Pattern Observation 61
- Eye Pattern Rise Time 61
- Trigger Mode 64
- Controlling the Vector 71
- Vector Pane Menu Selections 73
- Composite Gamut 76
- RGB Gamut Display 78
- Picture Display 80
- Timing Display 84
- Timing Pane Menu Selections 86
- Alarm Display 87
- Alarm Status Display 89
- Audio Display 92
- Audio Scales 93
- General Operation 100
- Expanding the Audio Display 101
- Option Display 102
- Display 103
- Video Metadata 105
- Teletext 108
- *NOTE: Y=Luma and C=Chroma 110
- T.S. Format 114
- Embedded Audio Data 115
- VTM Classic 116
- Timing Custom Display 123
- Presets 125
- Preset Setup Menu 125
- Capturing a Display 126
- Clear Captured Frame 127
- Clear Captured Data 127
- Navigating the Setup Menu 129
- Setup Menu and Alarm Tables 130
- Global Setup Menu Functions 131
- NOTE: LT=Light and DK=Dark 155
- Video Format Menu 159
- Waveform Setup Menu 159
- Eye Pattern Setup Menu 161
- Vector Setup Menu 161
- Gamut Setup Menu 162
- Picture Setup Menu 163
- Display Setup 166
- Freeze From Clock 167
- Communications Setup 168
- Baud Rate 169
- IP Address 169
- Subnet Mask 169
- Gateway 170
- GPO Out 1 and 2 Polarity 171
- GPO Out 1 and 2 Setup 171
- System Setup Menu 172
- File Navigator 176
- Flash from USB 177
- Figure 4-9. About Screen 178
- Setting Alarms 179
- Format Change 180
- Digital Gamut 181
- EDH – SD 181
- Loss of Carrier 183
- Loss of Video 183
- Loss of Reference 183
- Letterbox – SD 183
- Pillarbox - HD 183
- Picture Shift 184
- Captioning 184
- Eye Jitter 185
- Timing Alarm 185
- Loss of Signal 185
- Analog Gamut 186
- Sync and Burst 186
- Burst to Chroma Phase 186
- Vertical Blanking 187
- SC/H Phase 187
- Time Code Alarm Descriptions 188
- Alarm Reporting Setup 189
- CRC Change 189
- ETR 290 1 190
- Priority 190
- ETR 290 2 191
- ETR 290 3 192
- RST Enable and Repetition 193
- MGT Range 193
- STT Repetition 194
- RRT Repetition 194
- VCT Repetition 194
- EIT Repetition 194
- Section 6 ♦ External Control 195
- External Control 196
- Mouse Operation 197
- SpyderWeb II 197
- Browser Interface 198
- Tab/Tab Details 199
- Web RCU 200
- SNMP Communications 201
- Section 7 ♦ Troubleshooting 203
- Warm Start 204
- Cold Start after VFlash 204
- Troubleshooting 205
- Appendix A ♦ Specifications 207
- Video (continued) 208
- DVI-I Output 208
- Audio Options 208
- Audio Options (continued) 209
- Control 209
- Control (continued) 210
- Time Code 211
- Eye Pattern 211
- Eye Pattern (continued) 212
- Jitter Display 212
- SDI Freeze 212
- Data Analyzer 213
- CRC Error Display 213
- Closed Captioning Displays 214
- Gamut Display 214
- Magnification 214
- Specifications 215
- Environmental 216
- Standard Accessories 216
- Console 216
- Display Drivers 216
- Video Input Options 217
- Other Options 217
- Appendix B ♦ Pinouts 219
- Pinouts 220
- Appendix C ♦ Glossary 225
- Glossary 226
- Index-1 235
- Index-2 236
- LFE, 3-66 237
- Index-4 238
- Index-5 239
© 2020, manymanuals.com. All rights reserved. | 1.167 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals